Excessive encoder deviation from SVC estimate
Olası Nedenler
- Excessive deviation between encoder feedback speed and SVC estimated speed
Çözüm
- Check for encoder disconnection
- Ensure proper motor parameter settings
- Ensure motor auto-tuning performed
Resolver encoder disconnected
Olası Nedenler
- Resolver encoder disconnected
23-bit encoder disconnected
Olası Nedenler
- 23-bit encoder disconnected
Çözüm
- Check 23-bit encoder wiring
Hız değişkeni overflow
Olası Nedenler
- Hız referans hesaplamada overflow;parametre değeri sınır dışı
Çözüm
- Hız referans parametrelerini kontrol et;servo sıfırla
Anlık aşırı akım (瞬时过流)
Olası Nedenler
- Çıkış kısa devresi;IGBT anlık koruması;motor arızası
Çözüm
- Motor ve kablo izolasyonunu kontrol et;IGBT modülünü test et
Sürekli aşırı akım (持续过流)
Olası Nedenler
- Yük çok ağır;kazanç çok yüksek;motor parametresi yanlış
Çözüm
- Yük azalt;akım kazancını düşür;motor parametrelerini doğrula
EEPROM read/write fault 1
Olası Nedenler
- EEPROM read/write abnormality
Çözüm
- For communication write parameters check RAM addresses and mapping
- Contact Inovance to replace control board if EEPROM chip damaged
EEPROM read/write fault 2
Olası Nedenler
- EEPROM read/write abnormality
Çözüm
- For communication write parameters check RAM addresses and mapping
- Contact Inovance to replace control board if EEPROM chip damaged
EEPROM read/write fault 3
Olası Nedenler
- EEPROM read/write abnormality
Çözüm
- For communication write parameters check RAM addresses and mapping
- Contact Inovance to replace control board if EEPROM chip damaged
EEPROM read/write fault 4
Olası Nedenler
- EEPROM read/write abnormality
Çözüm
- For communication write parameters check RAM addresses and mapping
- Contact Inovance to replace control board if EEPROM chip damaged
Pozisyon sapma aşımı (位置偏差过大)
Olası Nedenler
- Yük çok ağır;kazanç düşük;komut çok hızlı
Çözüm
- Pozisyon sapma limitini artır;servo kazançlarını optimize et;yük azalt
Pozisyon sapma uyarısı
Olası Nedenler
- Pozisyon sapması uyarı eşiğini aştı (kritik değil)
Çözüm
- Uyarı eşiğini artır;servo kazançlarını optimize et;yük azalt
Motor auto-tuning error - stator resistance
Olası Nedenler
- Auto-tuned stator resistance out of range
Çözüm
- Correctly set F1-02 (rated voltage) and F1-03 (rated current) per motor nameplate
Motor auto-tuning error - rotor resistance
Olası Nedenler
- Auto-tuned rotor resistance of asynchronous motor out of range
Çözüm
- Ensure auto-tuning performed after motor stops
Motor auto-tuning error - no-load current
Olası Nedenler
- No-load current and mutual inductance exceed allowed range
Çözüm
- Set motor parameters per nameplate
- Ensure motor has no load before auto-tuning
Motor auto-tuning error - back EMF
Olası Nedenler
- Auto-tuned back EMF of synchronous motor out of range
Çözüm
- Set F1-02 per motor nameplate
- Ensure motor has no load before auto-tuning
Inertia auto-tuning error
Olası Nedenler
- Inertia auto-tuning fault
Çözüm
- Set F1-03 per motor nameplate
Encoder hatası (编码器故障)
Olası Nedenler
- Encoder kablosu kopuk;encoder arızası;gürültü
Çözüm
- Encoder kablo bağlantısını kontrol et;ekranlı kablo kullan;encoder değiştir
Encoder bağlantı hatası (编码器接线错误)
Olası Nedenler
- Encoder kablo bağlantısı yanlış veya kopuk
Çözüm
- Encoder pin bağlantısını şemadan kontrol et;kablo bütünlüğünü test et
Encoder gürültü hatası (编码器噪声故障)
Olası Nedenler
- Encoder sinyal kalitesi düşük;parazit;kablo kalitesi yetersiz
Çözüm
- Ekranlı kablo kullan;ferrit core ekle;encoder kablosunu güç kablolarından ayır